How I Built It: Old Airplane To Contemporary Light Sculpture That Connects To NASA & Rest of The World

How I Built It: Old Airplane To Contemporary Light Sculpture That Connects To NASA & Rest of The World

by Daric Gill

{Time-Lapse Video of Process Above}

Installed at the Columbus Museum of Art

The Imagination Machine is an interactive sculpture that communicates with NASA, is motion sensitive, tells time, and has a feature that can be remotely controlled from anywhere in the world. It’s made from one of the two wings of a Flying Flea aircraft, strips of individually programmable LEDs, and the brains of a Wi-Fi enabled robot. Part of The Living Machine series, this responsive sculpture takes a look at the emotional intelligence of imagination, as displayed by a robot.

A wooden truss supports the wings, lights, and electrical controls from above. There are two acrylic cases that are packed with brains, power supplies, and sensors to make this sculpture work. In this article, you can explore the build process from start-to-finish.

About The Wing
The plane without the wings attached.

At almost 19 ft long ( ~5.8 m), this wing is one of two pulled from a real bi-plane. The Flying Flea, or (Pou du Ciel literally “Louse of the Sky” in French) is a large family of light homebuilt aircraft. The plane was a generous donation by Mark Curtner in connection with the Historic Grimes Field Airport in Urbana, Ohio. Ohio’s only airport with 3 Museums on Field: The Champaign Aviation Museum, the Grimes Flying Laboratory, & Museum and the restoration wing of the Mid America Flight Museum of Texas.

As you can see from the photos in this article, the wing is segmented into 3 parts (two shorter wing ends + longer middle section). This allows the wings to fold up and inward for tighter storage.

In truth, this wing is actually the ends from one wing and the center from the other. The remaining middle section had some primer on it, rendering it no longer translucent enough that light would pass through. Any pilot will notice that the wing is also flipped upside down, showing the sexier rounded edge to the viewer below.

The Electronics

While the wing itself is split into three parts, the electronics are split down the middle in halves. Each half has a separate Wi-Fi enabled brain, corresponding lights, and electronic hardware. The brain holds around 27 pages of codes that loop over and over. These codes calibrate and get feedback from 4 separate motion sensors, activate Wi-Fi and make frequent requests of data from NASA and a server (called MQTT) that holds any communication until a valid Wi-Fi handshake is made, control various pins (that do anything from trigger a relay switch to direct electricity from a large power supply, to modulating the signals that change each LED on the light strips, to telling time, and more). The main brain is a 2-layered stack consisting of an Hazzah32 micro-controller and Adalogger + RTC board made by a successful female-owned company called Adafruit.

Huzzah32 Feather with ESP32 wi-fi board & Adalogger RTC

This paragraph is jargon-heavy (sorry): The Hazzah32 is an Arduino friendly ESP32-based Feather, made with the official WROOM32 module. At the moment, it is meant for intermediate and above developers, as the documentation can be a little daunting. To its benefit, each of the pins can be hard coded to do several different functions. Truthfully, much of the time working on this project was learning how this new board worked and growing into the shoes worn by such an ambitious project.

The light strips are RGB WS2812b 5050 LEDs (often rebranded as Neopixels ). While the strips look simple, each bright spot is a module comprised of a tiny red, green, and blue LED + a little driver. This means that each color and light bulb has 3 uniquely addressable lights that can be controlled independently. In total, The Imagination Machine has 2,700 individually addressable LED lights and can modulate many colors with ease. I used a reworked version of the adaptable open source FastLed codes.

You’ll notice that I go through several iterations of designs, homemade boards, LED configurations, and layouts. The great size and technical scope of this project was purposely outside my normal comfort range. What you’re seeing is the honest proof that I really came up with the final goal and had to truly learn what I was doing along the way. It was an exciting and deep journey through many unknowns. I’m appreciative of all the new knowledge that was born from so many trials along the way.

The Imagination Machine
June 2019
Medium: Reclaimed airplane wing, LED lights, Wi-Fi enabled Adafruit Hazzah32 micro-controllers, Adafruit Adalogger with Real Time Clock, PIR motion sensors, electronics, and poplar.
226” x 48” x Dimensions Variable

{To see the finished piece in action, click here}

Leave a Reply

Please log in using one of these methods to post your comment: Logo

You are commenting using your account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s